Monday, September 20, 2010

Centerboard



CB  after  successful refinishing


Centerboard Refinished

In preparation for the 100 mile WaterTribe NC Challenge,  the Dawn Patrol's centerboard (CB) needed to be refinished.  We had noticed a crack between the horn and the blade while we were sailing with Spartina in June.  We could also see "oyster-shell" wear on the tip of the blade.  

The process of removal, refinishing, re-installation, and testing (during the NCC) was successful. Details of the process  --far beyond what anyone should want to know--  are illustrated below.

How long does a CB last?   Wooden parts that are encapsulated in epoxy have to be monitored.  Any cracks, dents, damage or water infiltration deserve repair.


Sometime in the next year or two we may want to replace the CB with a newly built lead-weighted CB that will require a remodeled trunk. This original CB should last until then now that it has been refinished.


Look at that crack! 

It appeared that water infiltrated the wood via a crack.  SandyBottom: "Hmm maybe this explains why that centerboard seemed tight, likely swelling from water in the crack."   
SOS:  "I don't think the damage is from hitting big rocks.  Looks like water infiltration."

Port side: abrasion, crack, water damage

Port side: abrasion, crack, water damage

Port side: abrasion, crack, water damage

Port side: abrasion, crack, water damage

Port:  "oyster-shell" abrasion near the epoxy-hardened nylon-rope edge

Starboard:  "oyster-shell" abrasion near the epoxy-hardened nylon-rope edge
The board appeared to be fixable, despite the crack, so we undertook repairs and refinishing.  The handle is bolted into the blade (with 3 countersunk 4" SS screws).  The crack appeared on the port side but not the starboard side of the CB.   With the repairing and refinishing, we hope to have a few more months of use of this CB.  


Belt-Sanding the CB

After removing it from the boat,  I took the CB to the wood-working shop at Fitch Lumber in Carrboro and asked the helpful folks there to run the CB through their planer to take off  1/16 of an inch on each side.   Their planer uses a large sanding belt (rather than knife blades)  so it works well on composite materials such as this.   Cost: $5.  Time: 5 minutes.    Here is the result ....
 
Starboard side after pass through the planer

 
Port side after pass through the planer
 
Port side has crack



Starboard side
Careful sanding by hand and with a random-orbital sander came next to prepare for new fiberglass.


Epoxy Repair and Fiber glassing

Warming the wood prior to applying epoxy may have helped to draw the thin epoxy into the cracks.  This was followed by application of a small amount of thickened epoxy in the cracks.  Next, some new layers of 6 oz fiberglass cloth were on each side.  While doing this, the leading edge, trailing edge and tip were encapsulated in epoxy.  The trailing edge can thus become razor-sharp.   Result...

Ready for final coats of epoxy.
Checked the fit of the CB in the CB trunk at this point,  then applied three final coats of epoxy to fill the weave of the fiberglass cloth.   Re-finishing all done!   That was the easy part...


Re-installation

Installing the CB in the boat again,  as well as removing it prior to the refinishing work,  was the tedious part of the entire process. 

The CB pivots on a 3/8"-diameter stainless steel (SS) pin.  The pin is captured by port and starboard wooden disks ("caps".)  Each cap is held in place by 3 SS screws.  The CB and pivot pin are exposed to water, of course, so a silicone gasket between the cap and the trunk is necessary.  To create this, 100% silicone gel is applied to the cap.   
Starboard cap is in a storage hatch in cabin

The port cap is located and easily accessed in the footwell inside the cabin.  In contrast the starboard cap is deep inside a storage compartment in the cabin   --so I would need to become a human pretzel or shrink to the size of a puppy to easily access it.  It is easy to see, or easy to reach, but not easy to reach while you can see it. 


Webcam technology seemed promising but the images were slightly time-delayed.  Ultimately the human pretzel approach was required.   I managed to take care of the removal stage, and re-installation of the port cap.   Alan arrived just in time to reinstall the starboard cap.  Thanks Alan!


New Caps

The caps put in place during the re-installation were newly created from marine plywood;  the original caps were slightly damaged during the initial removal step.  Making new caps was easy:  epoxy-sealed disks of plywood made with epoxy-lined screw holes.   Piece of cake. 


Slotting the CB into the trunk    

Adequate access to the CB slot at the beginning and end of the process required sliding the boat a few feet off its trailer.  

Boat slid back 4 feet

Supporting the stern with 6x6 cut-offs

In normal position on the trailer, the CB comes to rest on the center roller of the trailer if released.


Appreciation

Thanks to Alan for his assistance and expert advice.


Speed: Sails, Oars, Motor


A look at the GPS data from our 8-day 200-mile coastal cruise in June 2010.


Excellent trip reports about our June cruise with the Spartina are already available in a brief summary by SandyBottom (photo at left) and especially in The Log of the Spartina by Steve Earley (that's Spartina in the background in the photo at left.) 

Steve has raised the enjoyment of small sailboat cruising to a fine art. He really knows how to savor the entire experience --from the anticipation and planning, to the adventure itself, to looking back with great photos and stories. Who knew even the planning stage could be so much fun? 

This post provides a complementary look at (1) the ups-and-downs of sailing speed and (2) our first experience sailing with a motor on a multi-day cruise.

Motor or no motor?

Our use of the motor was fairly minimal; what if we had used our lovely oars instead? Would an electric propulsion system have served as well?  For these questions, we have some data!

To my eye, hanging a motor on the transom of our Core Sound 20, Dawn Patrol, is a bit like painting a mustache on the Mona Lisa. We built the Dawn Patrol for WaterTribe adventure races, for daysailing, and for coastal cruising. We carry beautiful 11’ oars from Shaw & Tenney. I never envisioned needing a motor. So… when Steve Earley suggested the wonderful idea that we bring Dawn Patrol and tag along with the Spartina on a spring cruise, I had to think hard about painting on that mustache. The photogenic Spartina hides her motor in an engine well. Unfortunately, the stern freeboard on our Dawn Patrol is too low for hiding a motor. If we followed the proposed routes, would we be able to keep up with Spartina? “Yes”, if we packed a motor. Without a motor, wind and tide would probably dictate some on-the-fly route changes and delays. Good friend Ken generously offered to lend us his 2 hp, 28 lb, 4 cycle, Honda outboard. We charted and considered possible route variations and alternatives that might work well for sailing and rowing without a motor --as usual. Ultimately, we decided to follow the adage “When in Rome, do as the Romans.” We gratefully borrowed Ken’s motor. It was a good choice. The cruise was a great new learning experience, we were able to have a relaxed enjoyable time, and we had a blast cruising with Steve and Bruce. The many advantages of cruising with a motor made the trip more pleasant, saved us time for favorite activities, and avoided rowing in high temperatures. Given that we have a motor onboard, the disadvantages of carrying the motor (visually unappealing, extra weight, sheet snags on the motor (rarely), having to store the spare fuel somewhere) are not ameliorated by minimizing its usage. If I’m paying the price of these disadvantages, it would be foolish not to benefit from the advantages.

Our GPS Track

We used a Garmin GPSmap 76csx handheld chartplotter set to store our track by recording the latitude and longitude (lat, lon) every 20 seconds. The actual elapsed time between points was variable but averaged 20 seconds. There were a few (lat, lon) values in our track that were obviously in error. Each of these was easy to spot because the corresponding instantaneous speed was rediculous; e.g., 256 knots. The best thing to do is to delete such points from the track --which is exactly what I did. BlueChart software from Garmin was useful for charting our track and allowed me to export the data [lat, lon, time] to the GPX format (i.e., special HTML code) for use with other software.


Speed

In the speed graphs for our cruise, contributors to large variations in our speed included beating upwind into chop, tacking, and varying winds. For example, when beating into chop our speed can alternate rapidly between 6 knots and 2 knots. In contrast, our speed was much more constant when the hull was planing at 7 knots or when we were running downwind at 4-5 knots.

A little motoring

We traveled 207 nautical miles (nm) according to our GPS. Of those, 29 nm relied on the motor or motor+sails. We used a total of 0.95 gallons of gasoline (3.6 liters). Most of our uses of the motor were arguably optional but were desirable for convenience, for saving time and staying on schedule, or as a remedy for crew fatigue and impatience. We relied on the motor the most on Day 4 during 3 hours (9 nm) without wind and via narrow channels. In that case the alternatives included waiting for wind, rowing in the heat of the day, or changing our plans and perhaps rowing after sundown, or combinations thereof that would put us off our intended schedule.

For our next cruise

Would I use an outboard on our next multi-day cruise? Yes, probably. In the past I’ve enjoyed cruising (and racing) without a motor. To do so requires careful planning, a flexible schedule, and a patient crew. Cruising with a motor gives the crew more options and greater control over their schedule so that a desired route can be followed without delay or modification. The choice of whether to leave the motor at home depends on considerations that include the weather forecast, the routes desired, crew preferences, crew characteristics, and any scheduling constraints. How do I feel about about the motor now after our June cruise? To my eye it is still as visually unappealing as a moustache on the Mona Lisa, but I have a greater appreciation for the advantages and options it gives the crew. It may be relative quiet as motors go, but the noise it makes reminds me of a jackhammer. But, if I have to look at that darn thing while sailing, then I’m certainly not going to hesitate to use it for convenience.  Like every aspect of small boats, the motor has its advantages and disadvantages.

Choice of motor

I expect we will buy our own Honda 4-cycle, 2-hp, air-cooled, long-shaft outboard in the near future. This is a relatively simple engine seems more than adequate. A less conspicuous and quieter motor would be preferable. An electric motor might be used, but with the current state of battery technology an electric propulsion system could be heavier and less capable than an internal combustion engine. Battery power might be expected to deliver 3 hours of propulsion (as was needed on Day 4), but for a multi-day cruise we would need an adequate number of batteries recharged by large solor panels and a small wind generator --which would still lead to having nappealing machinery mounted on the boat.


Day 1
Total: 13.1 nm in 3.9 hours
Motor: 0.3 nm in 0.3 hours

June 18. The light breeze and flat water at the friendly boat ramp and low dock at Potter’s Marine made launching down North Creek a piece of cake. Sailing away from the dock would have been too easy. Instead, we decided to start our trip by making our very first use of the motor --just to gain some experience with it. I started the motor, reversed it, and backed away from the dock. The slack main sheet immediately snagged on the end of the dock. Darn! Lesson learned, we un-snagged and motored away for three minutes toward the Pamlico River, and then switched to the beautiful quiet of sailing without the aid of internal combustion. The wind was ESE at 11-12 knots as we tacked down the Pamilico River passing Indian Island and Reed Hammock. Our speed dropped from 5-6 knots to 2 knots after entering Goose Creek and the ICW. We spotted Spartina at anchor in Wilkerson Creek (faux Dixon Creek) and headed in tacking at 1 knot. Spartina had started and arrived 1-2 hours ahead of Dawn Patrol. They had tacked right up to the entrance of the creek (to within 500 feet of their anchorage) and then the wind was blocked by trees so they cranked the outboard and maneuvered in. By the time we had tacked to the entrance it was dinner time and we were eager to arrive. In the vanishing headwind some alternative propulsion was desired. Our oars were already mounted in the oarlocks so we rowed for a few minutes before impatiently deciding to motor on in and to “raft up” next to Spartina. After dinner we stowed the oars in their usual place under the cockpit’s coamings --where they remained for the next seven days.

In the SPEED figure below, instantaneous speed values (black dots) are shown with connect-the-dots (tan), smoothed trend (red), and intervals of motoring (gray band).   The MAP image below shows the path of the Dawn Patrol (red track) and the path of the Spartina (black dots).  






Day 2
Total: 26.1 nm in 10.3 hours
Motor: 2.3 nm in 0.8 hours

June 19.  With SE winds 4-9 knots we sailed south and southeast 5.2 miles down the ICW. Our speed ranged from 1 to 5 knots and eventually depended on frequent short-tacking as the ICW narrowed. By the time we could see the Hobucken Bridge we were ready to power up the motor. We cruised the narrow ICW with the motor for 2.6 miles, at about 2.8 knots, until the waterway widened into Gale Creek. Along the way we passed up the opportunity to follow Spartina out Jones Bay so that we would have an hour to visit Graham Byrnes. After having listened to the motor for 50 minutes we were happy to switch back to quietly short-tacking out toward the Bay River. Our speed varied from 2 - 4 knots while short tacking, but once headed on a broad reach in the Bay River our speed was constant at 4 knots. Raising the mizzen stays’l bumped our speed up to 5 – 6 knots. At Chapel Creek we visited Graham Byrns and his daughter Beth at the dock and workshop of B & B Yacht Designs. Graham took a moment to snap a few photos of the CS20 Dawn Patrol which, apart from the cabin, was entirely his design. It was a real treat to see Graham and Beth, and to see the exciting projects in the B & B workshop. At the moment they were busy finishing (spraying glossy red paint on) the efficient powerboat “Marissa” --his award-winning design. After a swim to cool off from the mid-day heat Dawn and I headed back out on the Bay River toward Bonner Bay where Steve and Bruce were looking to catch some fish. With afternoon temperatures above 90F thunderstorms threatened in the distance and the wind was shifting locally from E to NE. Turning SE into Bonner Bay gave us a good 4-5 knot ride to our anchorage in Long Creek. It has been a great day. Motoring those 2.6 miles at 2.8 knots for 50 minutes in the narrow ICW contributed to that. The alternative would have been rowing at perhaps 1-2 knots into a very light headwind for probably 150 minutes on a hot day. That would be fine if we were doing an adventure race, but less desirable for a vacation cruise.




Day 3
Total: 25.1 nm in 7.39
Motor: 3.7 nm in 1.7 hours

June 20.  With a favorable WSW wind at 5 knots, it seemed that we would start the day by sailing downwind through the narrow channel of Dipping Vat Creek toward Pamlico Sound. The narrow channel turned out to be partly obstructed by a pier and an overhanging raised gate. While we were slowing our approach and still trying to come close enough to get a good look at the obstructions, Spartina squeezed through on their second try. Still moving forward at less than 1 knot, we elected to play it safe by dropping our masts. Beaching the bow onto a mud bank brought us to a stop. We lowered the sails, rotated the masts down, and gathered in loose lines in less than two minutes. We could have rowed or skulled through the gate but… we had a motor! We powered through the gate and continued motoring for another 12 minutes the entire length of the 0.4 mile-long ditch at 3.5 knots, the wind at our backs. Yes, we easily could have rowed most of that, or even raised sails again just past the gate. At the end of the ditch we dropped anchor in Fisherman Bay. Five minutes later the masts and sails were up, the anchor was onboard, and we were away. Our speed jumped up to 5-6 knots and stayed there as we rounded Maw Point and entered the mouth of the Neuse River. The route to Oriental gave us 2 hours sailing on a reach and then 3 hours doing a few long tacks back and forth across the Neuse River. Our last tack was too long as it took us to the far side of the river just as there was a lull in the wind. We needed two more tacks to reach Oriental. Where were the winds kicked up by those typical afternoon thunderstorms? There were no thunderstorms. After thirty minutes of creeping along at 2.5 knots and roasting in the 93° (F) heat, we decided to use the motor. After about 25 minutes of motoring toward Oriental at 3 knots, we saw no sign that the wind would return and we opted to furl the sails as we cruised along. After that it took another hour to reach the harbor and the Oriental Inn Marina docks. The wind did pick up again during that hour, but we motored on eager to arrive because the heat was oppressive in spite of our hats, sun glasses, and the many liters of water we were drinking. By 2:15 were were sitting in the oasis of air conditioning in the Oriental Inn’s restaurant. Sipping numerous glasses of ice-cold tea, I felt my temperature drop to normal and my energy return. At about that time the wind out on the river was strengthening to 10-15 knots. We could have patiently waited for the wind, perhaps by taking a swim around the boat, and probably could have arrived in Oriental by 3:30 without using the motor. But as we enjoyed cold drinks in that heavenly air-conditioned oasis, we were thinking “it’s really hot out there” and not “we should still be out there.”


 
 



Day 4
Total: 39.5 nm in 11.5 hours
Motor: 9.1 nm in 3.0 hours

June 21.  The downwind run wing-on-wing eastward across the Neuse River was wonderful. The wind was increasing and our speed steadily climbed from 3 knots to 5 knots by the time we reached Turnagain Bay. It seemed that we would be able to sail downwind straight through Old Canal and then Thorofare Canal. But no. Somehow there was little or no wind in those narrow canals. In the bays between them we occasionally caught a little breeze. Dozens of dragonflies found us and made themselves at home on the Dawn Patrol and the Spartina as we motored, or occasionally motor-sailed, from the entrance to Old Canal to the exit from Thorofare Canal. We motored for almost 3 hours covering 9.9 miles (~3 knots per hour). Approaching the Thorofare Bay Bridge we passed through a tiny whirlwind (a ‘dust devil’ on land). We noted a few darkening clouds. As we sailed out of Thorofare Bay toward Core Sound, the western sky continued to gradually darken. On the eastern horizon Core Banks remained in full sun. The route down Core Sound was upwind. Tacking and following marked channels was a challenge. Our speed ranged from 3 to 6 knots due to frequent tacking and varying wind. By 2:00 as we passed Drum Inlet the western half of the sky was black and threatening. It was obvious that the storm was moving east, toward us, and it appeared that there was no way to dodge or out-run the thunder storm. At about 2:40 pm as the lightning and thunder approached closer we hove-to for a few minutes to don our foul-weather jackets and to put two reefs in the main and two reefs in the mizzen. Fortunately, we had reefed just in time. As the storm came further out over Core Sound (and us)… it vanished! In a matter of 30 minutes the sky changed from ominous black to clear blue. There were no clouds to be seen. Where did they go! That’s not what we were expecting, but who’s complaining? We hove-to at 3:15 to shake out all the reefs and shed the rain jackets; but his time rather than heaving-to in the usual manner, we cranked the motor and powered directly into the wind at about 3.5 knots for 7 minutes. This motorized alternative to the usual method of heaving to (fully sheeting in the mizzen and releasing the main sheet) stabilized the boat inspite of the confused chop, made the movements of sails more predictable, and did not require sheeting in the mizzen.



With full sails we tacked onward at 4-5 knots occasionally enjoying higher bursts of speed. After working our way far enough down Core Sound, we turned east for a short fast downwind ride over shallower water into The Swash --a tiny bay in Core Banks.

The Swash is a good place to be on a 93° (F) day. The evening was hot but there was a pleasant 10 knot breeze. We anchored in 4 feet of clear cool water and took a dip to cool off. As Dawn and I wondered how we could use the breeze to cool the cabin for more comfortable sleeping, we happened to think of rigging a wind scoop to direct the breeze into the companionway. Surprisingly, my rain jacket and four pieces of string made a perfect wind scoop. We enjoyed a constant 10-knot breeze funneled into the companionway that night. Aaahhhh! It was wonderful. We vowed never to cruise without a wind scoop henceforth.





Day 5
Total: 18.8 nm in 5.2 hours
Motor: 0.0 nm in 0.0 hours

June 22.  The morning winds were more-or-less SW at 6-10 knots. We sailed SSW down Core Sound at 2-5 knots to the eastern end of Harkers Island. There we turned SSE and cruised at a consistent 6.5-7.5 knots toward Cape Lookout Light on Core Banks. This fast hull-planing ride was the fastest of our 8-day cruise. (The hull speed of the Core Sound 20 is in the neighborhood of 6.2 knots.) Our speed dropped and became much more variable, at 2.5 – 5.0 knots, as next we tacked SSW through Barden Inlet past the lighthouse. Finally, we turned west on a 3-5 knot reach to Power Squadron Spit. There we planted our anchor right on the beach and immediately began “chilling” in the cool clear water. Arriving at noon gave us an entire afternoon of cool swims, hopeful fishing, and walks on the beaches. It was another hot day but what a great place to be on a hot day. A sunshade tarp rigged above the cockpit and the makeshift wind scoop cooling the cabin made our visit all the better. And, three cheers for a day without using the motor! Well…. almost. At dusk we did use the motor for a minute to relocate the anchor 50 feet out in deeper water. Yes we could have used the oars instead.


 
 



Day 6
Total: 13.8 nm in 3.6 hours
Motor: 2.4 nm in 0.6 hours

Using our GPS we closely retraced our track from Day 5 back to the eastern tip of Harkers Island. The wind was SW 8.5-13 knots giving us an easy 5-7 knot ride out of Barden Inlet and into Back Sound. That was easy! (Where is the that-was-easy button when you need it?) We then turned west to cruise along the Harkers Island waterfront more-or-less successfully following the channel markers to Taylor Creek. Going around the Middle Marshes I happened to notice that the GPS said 5 knots but visually it appeared we were moving through the water at only 1-2 knots. We were riding a conveyor-belt of current toward Taylor Creek. The entrance to Taylor Creek featured a red nun buoy lying on its side high and dry on a sand bar, current going our way, and a sudden lack of wind as we passed a stand of trees on Carrot Island. Dawn had previously fretted about sailing/rowing in Taylors Creek (worried about collisions), so we started the motor and began dropping the sails as we entered the Creek. Once in Taylors Creek, we could have sailed but I knew that with the motor puttering along Dawn was happy at the helm, able to relax and enjoy the view of interesting boats and waterfront. We motored to Beaufort Docks marina (37 minutes, 2.7 miles). The dock manager directed us, Dawn Patrol and Spartina, to a pair of slips. We maneuvered there by motor (6 minutes, 0.17 miles).
 




Day 7
Total: 35.0 nm in 10.4 hours
Motor: 10.2 nm in 2.5 hours

June 24.  At 6:00 am the winds in Beaufort were generally SW at 7 knots. We motored away from Beaufort Docks marina at 6:15 hoping to reach the drawbridge around the corner just in time for the 6:30 opening. We did not want to miss it because we knew the bridge would not open again until 8:00. It is likely we could have sailed to the bridge. But… we had a motor! Dawn prefered that we motor through the bridge. Fifteen minutes and 0.5 mile later we motored through the open bridge while thanking the bridge master. We motored another thousand feet into the Newport River before switching to sail power. The morning was beautiful out on the river. Our 4-6 knot downwind open-water speeds began to drop as we entered the ICW and sailed further and further up the narrowing waterway. At 8:25 we had reached the NC 101 bridge and our downwind run had faded to only about 2 knots. We started the motor and cruised at about 5 knots the next 6.3 miles (70 minutes). By 9:35 the waterway had widened to more than 400 yards and we were able to switch back to sails only. Compared to our relatively constant speed while motoring, our speeds from 9:35 to 11:15 in Adams Creek were quite variable due to the varying winds in the creek and due to frequent short tacking. By 11:15 we had escaped into the open waters of the Neuse River. Out on the river the wind was inconsistent. We spent the afternoon hunting the wind. At 2:15 we were passing Great Island and the mouth of Clubfoot Creek –gateway to the Harlowe Canal waterway. By 2:40 we were on the last long leg (bearing 310° true) of the transit to Beard Creek. We sailed close-hauled into very small chop because the wind had shifted to being primarly a west wind. Speed varied from zero to 5 knots. After our speed had dropped below 2 knots several times, we chose to start the motor (3:15). With the sheets released and both sails luffing we adjusted our speed to 2.5 knots. Then, sheeting in to take advantage of any breezes, we found that the sails often added 3.0 knots to our total speed. The motor kept our speed more consistent through the chop and the lulls. We motor-sailed 4.4 miles (65 minutes). The wind gradually strengthened. At 4:20 we rested the motor and sailed the remaining 2.1 miles to our anchorage in Beard Creek. Meeting up with Spartina there, we also used the motor momentarily to maneuver. In total we motored 11.3 miles during 155 minutes. Without a motor our day would probably have been at least 2-3 hours longer. That assumes we would have sailed to the drawbridge in time, rowed the 6.3 miles in the ICW, and patiently sailed the last leg to Beard Creek. Having the motor kept us on schedule --arriving at anchorage in time for a relaxing dinner by 5pm.






Day 8
Total: 11.6 nm in 3.6 hours
Motor: 1.1 nm in 0.5 hours

June 25.  How much was our speed reduced by sailing to New Bern with the ladder down? We’re not sure because we have not yet tried to measure that effect. After taking a cooling dip in Beard Creek the previous evening, I had neglected to fold it back up to its upright locked position. The ladder is mounted on the transom so that it is not visible from the cockpit. We sailed out of Beard Creek at 2-3 knots and sailed close hauled on a single bearing all the way to New Bern without realizing the ladder was dragging. The wind over our route was generally SW 4-6 knots with occasional gusts and lulls. In this more-protected part of the Neuse River the water was flat --chop and waves mostly less than 8 inches. Variability in our speed was relatively small. In the absence of sizable chop/waves, currents, and tacking, the only factors that remained to account for the variability in our speed were changes in wind, sail trim, and hull trim.

At 9:15 we were within a mile of the high bridge over the Neuse (US17) when we heard Steve’s conversation with the drawbridge master: “… and there’s another sailboat right behind us…” or something to that effect. We quickly started motor-sailing at 5 knots but almost immediately realized we were too far away to hurry. I regretted starting the motor too soon but decided to go ahead and power in because the wind had faded. We furled the sails and motored under the high bridge, through the drawbridge, and into the New Bern Grand Marina. After docking in our slip we noticed the ladder.

It was a hot day. From a low of 78° at 6:00 the heat climbed to 85° by 9:00, to 90° by noon, and top out at 95° (F) as we explored New Bern on foot.




In the SPEED figure above, instantaneous speed values (black dots) are shown with connect-the-dots (tan), smoothed trend (red), and intervals of motoring (gray band).   The MAP image above shows the path of the Dawn Patrol (red track) and the path of the Spartina (black dots).



   --Paul

Monday, August 23, 2010

Practice makes better

A year ago today, August 23-24 2009,  Alan and I were out in the Dawn Patrol putting in some practice time scouting the WaterTribe's 100-mile NC Challenge race course.  At the same time Dawn was making a similar effort in her NDK Explorer sea kayak.  Practice makes..... better.   

It was a rewarding adventure sailing from the beach on Pamlico Sound to Beaufort.  Although we covered only the first half of the course on that trip, we became good friends with the Harlowe waterway (under 3 bridges),  the Pamlico/Neuse waters rounding Piney Island point (with bombing range),  and the Newport River/Taylor Creek approach to Beaufort.  We gained ~ 3.5 hours of rowing practice.    In the Neuse we inadvertantly capsized the Dawn Patrol for the first time (ever),   proved that it was no big deal,  and gained the confidence to go back home and routinely practice capsize-and-recovery drills (on purpose).

“It’s a dingy, and capsize and recovery is a normal expectation”.  --Alan



Day1 and Day2


I previously posted a report of this scouting trip in the B and B Yachts Forum on the Mess-About website,  along with  45 photos and 4 weather charts posted on Picassaweb. 

Recently I took a new look at the GPS data for our sailing and rowing from that 2-day scouting trip. Here are those data along with a few highlights...


Day 1

The winds on the Pamlico Sound were initially light as we rounded Piney Island into the Neuse River.  We occasionally rowed in the hot sun for a moment or two whenever the sails hung lifeless and the Pamlico turned to glass.  By 2pm the afternoon storms had kicked in to send us beating through sizable chop up the Neuse in 16 knot winds with 20-24 knot gusts.  I was at the helm when we capsized.  Twenty minutes later we were all bailed out,  none the worst,  and on our way reefed to the max in increasing winds. 

The storms cleared away the heat of the day left us in cooler air.  By 6:40pm we needed to shake the reefs out. By 8:00 pm the wind had died.  In the cool of the evening I rowed for an hour to bring us to a good stopping point and anchorage in the mouth of Clubfoot Creek  --gateway to the Harlowe waterway.  As we glided along during that hour, the stars were out overhead,  silent lightning flashed in the far distances,  Alan prepared a hot dinner for us,  and for some unknown reason we were treated to a fireworks display in the sky over Morehead City / Beaufort  (our destination) on that moonless night.      



Key: GPS speed (black dots connected by tan lines), smooth curve (red), rowing (tan rectangle).
Garmin GPSmap 76CSx was set to record [lat, lon] and time at 20-second intervals.




Day 2

At 7:00 am we sailed off our anchor, stopped for 5 minutes at Matthews Point Marina for water, and then short-tacked the first 3 miles into Clubfoot Creek.  The next 2.5 hours introduced us to rowing into a 1.5 knot current through the beautiful Harlowe Canal and its three faces:  the gentle Neuse River flora and fauna of Clubfoot Creek,  skirting the Croatan National Forest via the narrow canal under a canopy of trees and spanned by three low bridges,   winding through the lush green and brown marsh grasses of Harlowe Creek to reach the open tidal waters of the Newport River.  It was another hot day but we had a wonderful adventure discovering the Harlowe waterway and verifying that we did indeed fit under the three bridges with a few vertical inches to spare.  Piece of cake.  

Rowing through Harlowe Creek


The ride on the Newport River into Beaufort on 13-17 knot winds was fast.  We reefed.  Approached the draw bridge and sailed through when it opened with oars at the ready. 

Then passing "Check Point #1" (CP)  we sailed on down Taylor Creek to the public boat ramp. Dawn was waiting for us (of course!) at a public boat ramp.  The 5-10 knot gusty wind blowing toward the ramp, together with low-tide banks of oyster shell and mud to the right and left conspired against us;  ultimately,  Dawn backed the trailer down the ramp into the water and Alan sailed the Dawn Patrol up unto the trailer. 


Key: GPS speed (black dots connected by tan lines), smooth curve (red), rowing (tan rectangle).
Garmin GPSmap 76CSx was set to record [lat, lon] and time at 20-second intervals.


We were out of the water by 5:25pm.   Dawn did not believe we capsized. As we told her about our weekend, we finally convinced her that we were not pulling her leg, and she was glad we had that experience under our belts.  We had cruised and scouted the first 65 miles of the ~100mile NC Challenge.


A Month Later

A month later in the NCC 2009 race,  Alan and I sailed and rowed the same 65 miles in half the time --in large part thanks to cooperative conditions.  The other half of the race course (from Beaufort around Harkers Island and up Core Sound back to the start/finish line) was another story.


Friday, August 13, 2010

WaterTribe North Carolina Challenge (NCC2009)

The WaterTribe's second annual  North Carolina Challenge  is just around the corner:  in 41 days, 19 hours, 33 minutes.  Many WaterTribe challengers like to wait until the very last minute to sign up.  Perhaps psych-ing out the competition goes hand in hand with stealth camping and/or sailing at night.   Dawn encourged me to be a good example and go ahead and sign up,  so I recently got with it and added Alan and myself to the growing roster of challengers.  Sailing the Dawn Patrol, we will be in "Class 4" which includes all monohull sailboats. 

In 2010.  Like the NCC'09,  the NCC'10 will be a 100 mile race from a Pamlico Sound beach on Cedar Island down to a checkpoint in Beaufort via the Neuse River and Harlowe Canal and then back up to the starting point via Back Sound and Core Sound.  As in 2009 there will also be a 50 mile race from Cedar Island down to Beaufort for those who prefer that distance.   Both races start together at 7:30 am on Friday September 24.

In 2011.  Next year there will be three races:  50 mile,  100 mile,  200-300 mile.   That new long race on the drawing board will be on a par with the venerable WaterTribe Everglades Challenge (EC).   Or, some of us suspect it could be even tougher than the EC.


A Look Back at NCC '09

Here's a look at some data from the wonderful adventure Alan and I enjoyed last year in the NCC'09 sailing and rowing the Dawn Patrol.  (No motors allowed!)

107 mile track recorded by GPS

Weather History 

Friday 25th  (Day 1 on the Neuse River and at Beaufort)
     AM:  winds  5-10 mph from the WSW becoming WNW
     PM:  winds 15-22 mph from the NE, max gusts 26-32 mph
     Air temperatures 70-86 (F)

Saturday 26th  (Day 2 on Back Sound, Core Sound, and Pamlico Sound)
     AM:  winds 10-20 NE becoming E,  max gusts 26 mph
     PM:  winds 10-20 E becoming ESE,  max gusts 26 mph
     Air temperatures 70-78 (F)

Sunday 27th   (Others still on Core Sound and Pamlico Sound)
     AM: winds 5-10 SE becoming WSW,  max gusts 20 mph
     Air temperatures 70-80 (F)



Figure 1:  GPS speed data for Day 1

The race started at 7:30 am on Friday September 25 with mild weather and good winds off the beach. On the Pamlico Sound the wind gradually faded.  Rounding Racoon Island into the Neuse River we rowed for a few minutes (11:15am).  Mid-day storms kicked in and sent us flying on a fast down-wind run up the Neuse River toward Clubhouse Creek.  The rains caught up with us there as we sailed up into the narrowing creek toward the Harlowe Canal.  In the canal we row/sailed or rowed in sprint mode (rowing highlighted by tan band).  The overcast sky and light drizzle of rain helped keep us cool as we rowed.  Otherwise, rowing on a hot humid day in full sun would have been much less pleasant.  Alan and I took turns rowing in 20 minute intervals.  Friends and family were waiting under their umbrellas on some of the first of the three bridges we passed under.  The current in the canal was initially unfavorable and less than 1 knot.  After rowing under the 3 fixed bridges the current became increasingly favorable.  Nearing our exit into the Newport River we had just about caught up with Graham Byrne's EC22, "Southern Skimmer",  the sky had cleared, the wind picked up,  and we were able to short tack out of the creek into the open waters of the Newport River.  We caught up with Graham and Randy at the draw bridge.  We heard the bridge master telling Graham on channel 13 that sailboats wanting to pass through should have auxiliary propulsion.  "Oh, I've got oars for that!" says Graham.  The bridge master was satisfied with that response.  We had our oars in ready position as both of our boats passed through the open bridge at about 7:00 PM.  As low tide was to occur at 8:10 PM,  the current through Gallant Channel under the bridge was favorable and minimal.  As we entered Taylor Creek the tidal flow was also minimal and we had no trouble sailing eastward on Taylor Creek.  In Taylor Creek on the Beaufort waterfront we spent a minute or two at the checkpoint (CP) and then found an anchorage at the east end of Taylor Creek for a few hours of sleep.


Key:  GPS speed (black dots connected by tan lines),  smooth curve (red),  rowing (tan rectangle). 
Garmin GPSmap 76CSx was set to record [lat, lon] and time at 20-second intervals.  


Figure 2:  GPS speed data for Day 2

It was a dark, humid, warm night.  At 3:30 am Alan happened to wake up and look out the window just as the "Southern Skimmer" sailed past our anchorage.  Oh no!   He was out of the door in a flash putting on his sailing clothes with one hand and raising the sails with the other hand while telling me to hurry up.   "Dad, let's go!"  At least I was sitting up, which seemed like good progress to me.  I was looking for my clothes having slept in just my underwear.  Alan: "Let's go, Dad!"    Paul: "Alan, I'm not dressed yet!"   Alan: "Oh.... in that case, as soon as you have your pants on we're going!"    I love you, Alan.  What a great son.  Rolling out of Taylor Creek and into Back Sound required very close attention to the chartplotter in order to navigate the shallows while tacking up-wind in the pitch black darkness.  No moon.  Couldn't see a thing.  The NE wind was 10-20 with gusts up to 26 mph.   Fortunately for me, Alan loves to sail at night and was as happy as a clam to press onward.  I, at that moment,  prefered to focus on the chartplotter in my hands.  Fully reefed and short tacking in Back Sound,  our speed bounced between 1 and 6 knots.  At that moment Graham and Randy aboard the "Southern Skimmer" had decided to pull off into an anchorage and sleep for 3 more hours.  We had no idea.  We were chasing, but chasing no one.   At dawn we wondered, "Where is Southern Skimmer?"  We spent a total of 8 hours beating upwind through big closely spaced chop on Core Sound wondering "Where is Southern Skimmer?".  The spray coming off the bow shot around the cabin and drenched both of us like a fire hose.  One of the registration letters on the starboard bow peeled off and was thrown into my lap.  Our speed was highly variable due to continually slamming into chop.  Consequently, our Anderson bailer in the sole of the cockpit could not keep up with the huge volume of spray coming in.  We found that we quickly had several inches of water in the cockpit if we stopped bailing manually.  Thank you very much, Core Sound.  "Where is Southern Skimmer?" we wondered.  We finally passed east of Chain Shot Island and Wainwright Island and turned west into Pamlico Sound at about 2:00pm.  The "Southern Skimmer" had taken a shorter route and at that moment seemed to "pop out" into Pamlico Sound just downwind of us.  They had eaten up the 3-hour lead we we had.  Now they would beat us to the finish line by 12 minutes. And, there streaking home along the shore was kayak racer Ardie Olson ("ArdieO") sprinting toward the finish.  He would beat us by 6 minutes.  Still reefed, we rode the big swells downwind planing at 8-10 knots.  What a ride!   Both Alan and I sat as far astern as possible and moved aft any other weight we could.  Ten minutes from the finish line, Alan lost one of his shoes overboard.  Folks on shore were baffled by seeing us suddenly sailing a tight 360.  After successfully picking up the shoe we finished the course.   Wow, what an adventure! 



Key: GPS speed (black dots connected by tan lines), smooth curve (red), rowing (tan rectangle).
Garmin GPSmap 76CSx was set to record [lat, lon] and time at 20-second intervals.


A year later, we rounded the same NCC'10 course but the weather conditions made that a completely different race.


--Paul

On-Deck Storage

The layout of the Dawn Patrol works well for a crew of two.  On-deck storage area around the cockpit includes space under the port and starboard coamings, space under the thwart,  and space under the fold-down rowing seats.
There's no denying that our nice dry cabin is a great place to toss gear for quick temporary storage when we are in a hurry.  To help organization, small storage hammocks contain small items and provide an attachment point for carabiners.  The cabin space is seven feet long, less than six feet wide, and less than four feet high   --just big enough for two people to sleep.  When the footwell is covered with its lid, the floor of the cabin is a single flat surface interrupted only by the centerboard trunk.

Carabiners sliding on a bungee under each coaming provide a way to clip small items (water bottles, map case, sunglasses case, etc) to the boat.

Either or both of the two rowing seats can be folded up or down.   The rowing crew can sit on either seat to row with one oar, or sit in the middle on both of them to row with two oars.   The rowing seats also offer a great place to sit protected from wind and spray. 

The 11' oars (Shaw and Tenney) are usually mounted under the coamings but can also ride in a 'ready' position flanking the cabin, resting in the oar locks with blades secured up near the bow.

For keeping food cool we carry a cooler that rides in the cabin's footwell while we are sailing.  At anchor we move the cooler to the cockpit where it sometimes serves as a small tabletop.  For daysailing we often carry a smaller cooler that can fit under the starboard rowing seat.

--Paul

Thursday, August 12, 2010

Within-Hatch Navigation

By the end of our 8-day 200-mile cruise in June with Spartina, Dawn and I could easily find items stored in the various hatches.  Having penciled in on a storage map at least a rough idea of where things were hiding was especially helpful at the beginning of the trip.  We had both contributed to packing the boat in a bit of a hurry.
This version of the storage map shows where everything finally came to rest after a whirlwind of packing and a day or two of sailing.  This figure is only intended as an aid to finding stuff,  and as an aid to thinking about where to put things next time.   Unlike a detailed checklist,  it does not say what exactly is in the "tool kit",  for example.  We picked up this idea from the Log of Spartina blog by Steve Early.  Here are links to some of Steve's posts about storage:




In one of those posts Steve said "I'll laminate this drawing back to back with a sheet of info about marinas, hotels and some other material and tuck it in with our charts."

Index of the day-by-day trip reports on Log of Spartina:





--Paul